The note order parameters provide control of a pre-programmed order of notes that are played at a preset playback rate. Once all notes are played, the arpeggio cycles from the start. When you play a single key, it is repeated. When you play multiple keys, the held notes are played one after the other. As you play additional notes, these are seamlessly added to the arpeggio. When you release notes, they are removed from the arpeggio. The arpeggio stops when you release all played keys (unless Latch mode is turned on in the Arpeggiator control parameters).
The Arpeggiator plug-in automatically assigns position identification numbers to each note in the order they are played. These position identification numbers associate an event, such as a note, rest, or a tie, with a particular step. This lets you switch between note order presets while retaining a rest on the third step, for example.
All note order parameters can be changed while an arpeggio is playing. Changes are immediate and are seamlessly applied to the running arpeggio.
Rate knob and field: Set the arpeggiator rate. Choose from: 1/4, 1/8, 1/16 (including triplet and dotted notes), and 1/32. You can also click the field to choose a value from a pop-up menu. The LED indicates the rate and briefly changes color at the start of each new cycle.
Direction buttons: Set the arpeggio direction.
Up: The arpeggio is played from the lowest note to the highest note.
Down: The arpeggio is played from the highest note to the lowest note.
Up/Down: The arpeggio plays up and down, from the lowest note; the highest and lowest notes repeat.
Outside-in: The arpeggio plays the highest then the lowest notes, then the second highest and second lowest, the third highest and third lowest, and so on.
Random: Arpeggiated notes play in a random order.
As played: All notes play in the order they were triggered.
Lock button: Works in conjunction with the As played button. When you first click the As played button, an open lock symbol is shown. Click the open lock symbol once you have triggered an arpeggio to lock the current note order, indicated by a closed lock. This note order and feel is retained for any newly triggered arpeggios, but with new notes replacing the original notes. Click the lock symbol again to clear the locked note order and to revert to the standard “as played” behavior. The lock state and note order can be saved with a setting.
Variation switch: Determine the type of note order variation. See Arpeggiator note order variations for details.
Oct Range/Inversions button: Switch between two modes: Octave Range or Inversions. The four-position Oct Range/Inversion switch below the buttons is used to determine the octave range or the chord inversion pattern.
Oct Range/Inversion switch: Determine the octave range or the chord inversion pattern. See Arpeggiator note order inversions for details on the four switch position behaviors in Inversions mode.
In Octave Range mode:
Position 1: The arpeggio repeats without transposition.
Position 2: The lowest note is transposed by one octave. Once repeated, the arpeggio restarts in the original octave.
Position 3: The first repetition is transposed by one octave, and the second repetition is transposed by two octaves. Once the second repetition is played, the arpeggio restarts in the original octave.
Position 4: The first repetition is transposed by one octave, the second by two octaves, and the third by three octaves. Once the third repetition is played, the arpeggio restarts in the original octave.
In Inversions mode:
Position 1: The arpeggio repeats without inverting the held notes.
Position 2: The arpeggio is inverted once during the first repetition. Once repeated, the arpeggio restarts.
Position 3: The arpeggio is inverted twice, once each during the first and the second repetition. Once the second repetition is played, the arpeggio restarts.
Position 4: The arpeggio is inverted three times, once each during the first, second, and third repetitions. Once the third repetition is played, the arpeggio restarts.